Methods of Mounting Saw-Toothed Metallic Wire on the Taker-in and Other Rollers of Carding Machine
DOI:
https://doi.org/10.3329/gubjse.v6i1.52047Keywords:
Carding, metallic wire, front face of wire teeth, transitional edges, obliqueness of wire teethAbstract
Two methods are used for mounting sawtoothed metallic wire on different rollers of carding machine. The taker-in roller of the machine is generally grooved one way starting from one end of the roller to the other end and metallic toothed wires are mounted into the grooves. In course of time teeth of wires are worn out as they interact with fibers and impurities. As a result quality of product is deteriorated gradually. So the general practice is to replace the worn-out wires with new ones. Close observation of gradual wearing out of wire teeth reveals that due to oblique disposition of the teeth, only one of the two transitional edges of the front face of the teeth is mainly worn out leaving the other transitional edge intact. This paper explains one patented method and proposes another novel one that utilizes this unworn transitional edge and thus improves quality of yarn and increases longevity of the wear. The first method proposes taker-in with grooves starting from both ends of the roller. Application of this method will enable spinners to utilize both the transitional edges of taker-in teeth by dismounting the wires from the groove first after some use and then mounting the same wire on the roller again but into the grooves that start from other end of the roller. The second method proposes use of two types of wires on the bare taker-in roller; one type is toothed and another is without teeth. They are mounted on the roller side by side and alternately. Incorporation of tooth-less bare strip of wire gives obliqueness to the toothed wire. This method also will allow utilization of unworn edge of teeth by dismounting the wire first after some use and then mounting them on the roller starting from other end of it.
GUB JOURNAL OF SCIENCE AND ENGINEERING, Vol 6(1), Dec 2019 P 27-32
Downloads
37
35
Downloads
Published
How to Cite
Issue
Section
License
Authors who publish in the GUB Journal of Science and Engineering agree to the following terms that:
- Authors retain copyright and grant the GUB Journal of Science and Engineering the right of first publication of the work.
Articles in GUB Journal of Science and Engineering are licensed under a Creative Commons CC BY-NC-ND License Attribution-NonCommercial-NoDerivatives 4.0 International License. This license permits Share — copy and redistribute the material in any medium or format.
Copyright and Reprint Permissions
- Individual contributions contained in it are protected by the copyright of Green University of Bangladesh.
- Photocopies of this journal in full or parts for personal or classroom usage may be allowed provided that copies are not made or distributed for profit or commercial advantage and the copies bear this notice and the full citation.
- Copyright for components of this work owned by others must be honored. Abstracting with credit is permitted.
- Specific permission of the publisher and payment of a fee are required for multiple or systemic copying, advertising or promotional purposes, resale, republishing, posting on servers, redistributing to lists and all forms of document delivery.
- Subscribers may reproduce a table of contents or prepare lists of articles including abstracts for internal circulation within their institutions.
- Permission of the Publisher is required for resale and distribution outside the institution. Permission of the publisher is required for all other derivative works, including compilations and translations.
- Except as outlined above, no part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, such as electronic, mechanical, photocopying, magnetic recording or otherwise, without prior written permission of the publisher.
- Permissions may be sought directly from the office of the executive editor of GUB Journal of Science and Engineering through E-mail at gubjse@fse.green.edu.bd.
Notice
- Responsibility for the contents of an article rests upon the author(s) and not upon the editor or the publisher. Therefore, on responsibility is assumed by the publisher for any injury and/or damage to persons or property as a matter of products liability, negligence or otherwise, or from any use or operation of any methods, product instructions or ideas contained in the material herein.
